USBASP Driver To easily install USB Driver (without requiring windows signature check) on Windows 10, and Windows 8 you can use Zadig tool. The detailed procedure can be seen here Also buy AVR-ISP 10Pin to 6pin Adapter PCB (Not included with USBASP V2.0 programmer). How to install Usbasp Driver in Windows 8.1 and Windows 10. Mini atmel avr isp v2.0 stk500 usb isp programmer, 1, usb cable, 1, 10-pin idc isp cable, 1, 10-pin to 6-pin idc isp cable, 1, eccn/hts. Special note on skill level, this is a simple soldering kit, but arduino as isp is a relatively immature process, and there are some rough edges.
Help! I've spent the last couple of hours banging my head against the wall. I was trying to update my firmware with my new usbasp programmer, and have only managed to erase my chip.
I bought the programmer off ebay (it says USBASP V2.0 - LC Technology), and wired an adapter cable with the following mappings (from Sanguino to programmer):
Indian styles for yamaha keyboard. 1 - 9 (MISO)
2 - 2 (VCC)
3 - 7 (SCK)
4 - 1 (MOSI)
5 - 5 (CS)
6 - 10 (GND)
When using, it, the 1284p is detected and has the correct signature, and I can successfully read and change the fuses, so the connection seems okay. However, when trying to upload a bootloader or marlin build, it always fails to verify as follows. Any ideas? The programmer itself only has a jumper for 3.3/5V (currently set to 5V).
>avrdude -C .etcavrdude.conf -c usbasp -p m1284p -U flash:w:SolidoodleMarlin.cpp.hex -v -D
avrdude: Version 5.4-arduino, compiled on Oct 11 2007 at 19:12:32
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
System wide configuration file is '.etcavrdude.conf'
Using Port : lpt1
Using Programmer : usbasp
AVR Part : ATMEGA1284P
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PA0
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page
Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW Max
W ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ---
-- ---------
eeprom 65 10 128 0 no 4096 8 0 9000 90
00 0xff 0xff
flash 65 10 256 0 yes 131072 256 512 4500 45
00 0xff 0xff
lock 0 0 0 0 no 1 0 0 9000 90
00 0x00 0x00
lfuse 0 0 0 0 no 1 0 0 9000 90
00 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 9000 90
00 0x00 0x00
efuse 0 0 0 0 no 1 0 0 9000 90
00 0x00 0x00
signature 0 0 0 0 no 3 0 0 0
0 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0
0 0x00 0x00
Programmer Type : usbasp
Description : USBasp, http://www.fischl.de/usbasp/
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.02s
avrdude: Device signature = 0x1e9705
avrdude: safemode: lfuse reads as DE
avrdude: safemode: hfuse reads as DB
avrdude: safemode: efuse reads as F8
avrdude: reading input file 'SolidoodleMarlin.cpp.hex'
avrdude: input file SolidoodleMarlin.cpp.hex auto detected as Intel Hex
avrdude: writing flash (110734 bytes):
Writing | ################################################## | 100% 59.31s
avrdude: 110734 bytes of flash written
avrdude: verifying flash memory against SolidoodleMarlin.cpp.hex:
avrdude: load data flash data from input file SolidoodleMarlin.cpp.hex:
avrdude: input file SolidoodleMarlin.cpp.hex auto detected as Intel Hex
avrdude: input file SolidoodleMarlin.cpp.hex contains 110734 bytes
avrdude: reading on-chip flash data:
Driver Usbasp Windows 10
Reading | ################################################## | 100% 57.39s
Usbasp V2 0 Driver Windows 10 64-bit
avrdude: verifying ..
avrdude: verification error, first mismatch at byte 0x0000
0x0c != 0x00
avrdude: verification error; content mismatch
Help! I've spent the last couple of hours banging my head against the wall. I was trying to update my firmware with my new usbasp programmer, and have only managed to erase my chip.
I bought the programmer off ebay (it says USBASP V2.0 - LC Technology), and wired an adapter cable with the following mappings (from Sanguino to programmer):
Indian styles for yamaha keyboard. 1 - 9 (MISO)
2 - 2 (VCC)
3 - 7 (SCK)
4 - 1 (MOSI)
5 - 5 (CS)
6 - 10 (GND)
When using, it, the 1284p is detected and has the correct signature, and I can successfully read and change the fuses, so the connection seems okay. However, when trying to upload a bootloader or marlin build, it always fails to verify as follows. Any ideas? The programmer itself only has a jumper for 3.3/5V (currently set to 5V).
>avrdude -C .etcavrdude.conf -c usbasp -p m1284p -U flash:w:SolidoodleMarlin.cpp.hex -v -D
avrdude: Version 5.4-arduino, compiled on Oct 11 2007 at 19:12:32
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
System wide configuration file is '.etcavrdude.conf'
Using Port : lpt1
Using Programmer : usbasp
AVR Part : ATMEGA1284P
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PA0
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page
Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW Max
W ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ---
-- ---------
eeprom 65 10 128 0 no 4096 8 0 9000 90
00 0xff 0xff
flash 65 10 256 0 yes 131072 256 512 4500 45
00 0xff 0xff
lock 0 0 0 0 no 1 0 0 9000 90
00 0x00 0x00
lfuse 0 0 0 0 no 1 0 0 9000 90
00 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 9000 90
00 0x00 0x00
efuse 0 0 0 0 no 1 0 0 9000 90
00 0x00 0x00
signature 0 0 0 0 no 3 0 0 0
0 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0
0 0x00 0x00
Programmer Type : usbasp
Description : USBasp, http://www.fischl.de/usbasp/
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.02s
avrdude: Device signature = 0x1e9705
avrdude: safemode: lfuse reads as DE
avrdude: safemode: hfuse reads as DB
avrdude: safemode: efuse reads as F8
avrdude: reading input file 'SolidoodleMarlin.cpp.hex'
avrdude: input file SolidoodleMarlin.cpp.hex auto detected as Intel Hex
avrdude: writing flash (110734 bytes):
Writing | ################################################## | 100% 59.31s
avrdude: 110734 bytes of flash written
avrdude: verifying flash memory against SolidoodleMarlin.cpp.hex:
avrdude: load data flash data from input file SolidoodleMarlin.cpp.hex:
avrdude: input file SolidoodleMarlin.cpp.hex auto detected as Intel Hex
avrdude: input file SolidoodleMarlin.cpp.hex contains 110734 bytes
avrdude: reading on-chip flash data:
Driver Usbasp Windows 10
Reading | ################################################## | 100% 57.39s
Usbasp V2 0 Driver Windows 10 64-bit
avrdude: verifying ..
avrdude: verification error, first mismatch at byte 0x0000
0x0c != 0x00
avrdude: verification error; content mismatch
Usbasp V2.0
avrdude: safemode: lfuse reads as DE
avrdude: safemode: hfuse reads as DB
avrdude: safemode: efuse reads as F8
avrdude: safemode: Fuses OK
Usbasp Driver For Windows
avrdude done. Thank you.
